Tamko TAM-RAIL Manuel d'utilisateur télécharger pdf

Straight Rail

Installation Instructions

Straight Rail Kit Components

• 6ʼ or 8ʼ TAM-RAIL Top Rail

• 6ʼ or 8ʼ TAM-RAIL Bottom Rail

• Balusters – Square or Colonial

• 6ʼ Square (13 ea.) or Colonial (14 ea.)

• 8ʼ Square (17 ea.) or Colonial (19 ea.)

• Brackets – Top Rail (2 ea.) Bottom Rail (2 ea.)

• 20 Coated Screws

• (17 ea.) 2 1/2” Stainless Steel Screws

• (3 ea.) 1 1/4” Stainless Steel Locking Screws

• 1 #3 Square Drive Bit

• Crush Block – 6ʼ Section (1 ea.) 8ʼ Section (1 ea.)

tape measure

hack saw

drill

level

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

ACTUAL STRAIGHT RAIL LENGTHS

Nominal Rail Length 6ʼ 8ʼ

Spaced for Colonial Balusters (Actual Rail Length) 70.5” 94.125”

Spaced for Square Balusters (Actual Rail Length) 72” 96”

.GH,9AD

GLLGE,9AD

JMK@DG;C

-IM9J=9DMKL=J

GLLGEJ9;C=L

.GHJ9;C=L

miter saw

Tools Required For Installation - Tape measure, miter saw or hack saw, #3 square

drive bit, power drill and level. For larger construction projects, miter saw and drill are

strongly recommended for quicker installation.

RAILING SYSTEMS

TAM-RAIL

10/07/08

JP55316

1. Install and prepare all mounting surfaces and posts to which new TAM-RAIL Railing will be installed. We sug-

gest using our innovative post mounting system or covering the wooden posts with our matching 3-layered post

sleeve.

2. Measure the inside opening between the posts or other mounting surfaces. NOTE: Conﬁ rm the opening is

not wider than the length of the rails provided in TAM-RAIL Rail Kit. (FIG. 1)

3. Lay the bottom rail beside the posts or other mounting surfaces with the baluster holes facing upward. The

rail should extend past the mounting surface on each side. Be sure to place the ﬁ rst baluster hole on each end

of the rail the same distance from the mounting surface. NOTE: If the baluster holes fall inside or directly be-

side a mounting surface, slide the rail approximately 2” in either direction to align baluster holes evenly

between mounting surfaces. When you have positioned your rail properly, mark and cut. (FIG.2)

4. Lay top rail beside bottom rail, making sure your baluster holes are aligned. Once properly aligned, mark and

cut to match bottom rail length. (FIG.2)

5. Locate the crush block (1 1/2” x 1 1/2” square proﬁ le used to support the railing section) in your TAM-RAIL

Railing Kit. The formula for crush block length is: Desired clearance from bottom rail to deck + 3 1/4” =

length of crush block. NOTE: When using the TAM-RAIL New England Post Ring, you must cut your

Crush Block to a minimum of 5 1/2” to allow for proper spacing. Once the block is trimmed to appropriate

length, insert into precut hole on the underside of bottom rail. Be sure to check with your local building code

ofﬁ cials for any height requirements.

6. Slide mounting brackets onto bottom rail. Place bottom rail between posts or mounting surface making sure

crush block is fully nested in bottom rail and the bottom rail is level. Once the bottom rail height is determined,

mount brackets on the post or mounting surface and attach with provided 2 1/2” screws. NOTE: When install-

ing screws, pre-drill holes using a 1/8” drill bit. NOTE: If installing TAM-RAIL Railing into a masonry wall,

masonry screws must be used in place of screws provided in kit. (FIG.3)

7. Insert balusters into pre-routed holes in bottom rail. Balusters are available for 36” and 42” rail height kits

based on the traditional two-inch clearance from the bottom rail to the mounting surface. Note: Colonial and

Square balusters are available for 36” rail height kits; only Square balusters are available for 42” rail

height kits. Be sure to check with your local code ofﬁ cials for any height requirements.

8. Slide mounting brackets onto top rail. Place top rail on balusters inserting balusters one at a time while hold-

ing at an upward angle. Make sure balusters are completely nested in top rail and level. (FIG.4)

9. Center top rail over bottom rail and mount brackets onto post or mounting surface. Attach brackets with

provided 2 1/2” screws. (FIG.5)

10. Level balusters vertically and place 1 1/4” (provided) locking screw through the top bracket and into the top

rail. Repeat for bottom rail. NOTE: Only one side (top rail and bottom rail) needs to be secured. There are

extra (1 ea.) 1 1/4” and (1 ea.) 2 1/2” stainless screws provided. (FIG.6)

For assistance, information regarding, or to receive a

copy of TAMKO’s Limited Warranty, contact us at

1-800-641-4691 or visit us online at tamko.com.

It is the responsibility of the installer to meet all building code and safety requirements and to obtain all

required building permits. These instructions are only a guide and may not address every circumstance.

TAMKO Building Products Inc. shall not be held liable for improper or unsafe installations. These

application instructions were current at the time of printing. To obtain a copy of the most current version of

the application instructions, visit us online at tamrail.com or call us at 1-800-641-4691.

1 2 3 4 5 6 7 8

TAM-RAIL 1

Résumé du contenu

Page 1 - TAM-RAIL

Straight RailInstallation InstructionsStraight Rail Kit Components• 6ʼ or 8ʼ TAM-RAIL Top Rail• 6ʼ or 8ʼ TAM-RAIL Bottom Rail• Balusters – Square or C

Page 2

Stair RailInstallation InstructionsACTUAL STAIR RAIL LENGTHSNominal Rail Length 6ʼ 8ʼSpaced for Colonial Balusters (Actual Rail Length) 78” 102”Spaced

Page 3

Post Mount & Post SleeveInstallation InstructionsPost Kit Includes:(1 ea.) 4” x 4” x 38” Post Sleeve(1 ea.) Structural Post Mount(1 ea.) 4” New En

Page 4

22.5° Angle Application(Tools Required: Tape measure, miter saw)1. Place the multi-angle brackets on the top and bottom rails making sure the bracket

Page 5

Instrucciones de Instalación de Barandas Rectas TAM-RAIL® cinta de medirsierra de ingletetaladronivelFig. 1Fig. 2Fig. 3Fig. 4Fig. 5Fig. 6LARGOS REALES

Page 6

RAILING SYSTEMSTAM-RAIL®Instrucciones de Instalación de Barandas para Escaleras TAM-RAIL®LARGOS REALES DE BARANDAS RECTASLargo Nominal de Baranda 6&a

Page 7

RAILING SYSTEMSTAM-RAIL®Instrucciones de Instalación de Montajes y Mangas de Postes TAM-RAIL®El Juego de Postes incluye:(1 c/u) Manga para Poste 4&quo

Page 8

RAILING SYSTEMSTAM-RAIL®Aplicación en ángulo de 22.5°(Herramientas requeridas: Cinta de medir, sierra de inglete) 1. Coloque los soportes de ángulo mú

Modèles reliés Straight Rail

Plus de documents pour Pour la maison Tamko TAM-RAIL

Voir le document Tamko TAM-RAIL Manuel d'utilisateur

Tamko TAM-RAIL Manuel d'utilisateur (12 pages)

Commentaires sur ces manuels

Pas de commentaire

Tamko TAM-RAIL Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Tamko TAM-RAIL. TAMKO TAM-RAIL User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés Straight Rail

Plus de documents pour Pour la maison Tamko TAM-RAIL

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Tamko TAM-RAIL